ACTICHEM Stone Sealer Pro Water Based Penetrating Sealer 5 LItre AP17205
Stone Sealer Pro
Penetrating sealer for natural stone and tiles
Product Description
Stone Sealer Pro is a premium water-based penetrating sealer designed to protect marble, limestone, travertine, granite, and bluestone. It uses advanced fluorochemical polymer technology to form a highly repellent surface, providing lasting protection for interior and exterior stone.
Stone Sealer Pro solves the challenge of protecting fine stone from stains, weathering, and oil or water-borne contaminants. Its vapour-permeable formula prevents moisture entrapment while preserving the natural finish. Ideal for use on walls, floors, patios, walkways, and feature areas, it offers up to 7 years of protection, is NATA-tested, and Green Star compliant. Clean with Actichem Tile & Grout Cleaner LF to extend performance. Not suitable for sub-terrain waterproofing.
Floors & hard surfaces
Sealant
Stone & grout
pH
Water-Based
Dilution
Ready to use
Fragrance
None
Safety
Non-hazardous
Colour
N/A
Pack Size
5lt, 15lt, 500ml, 2.5Lt
Surfaces
Natural Stone, Concrete & Masonry
Product Code
AP172
I
Additional Information
Benefits
Premium Protection: Offers up to 7 years of protection, independently performance-tested by a NATA-approved laboratory.
Dual Protection: Shields against water and oil-borne contaminants, including food and beverage stains, oil and grease, biological growth (mould and mildew), efflorescence, pollution, and weathering.
Natural Look: Maintains the original appearance of the stone without discoloration or alteration.
UV Stable: Suitable for both indoor and outdoor use, withstanding UV exposure.
Vapour Permeable: Allows the natural passage of water vapour, preventing moisture entrapment.
Non-Flammable and Low VOC: Safe to use with very low VOC content and Green Star Approved.
Green Star Approved: Meets the VOC requirements of Green Star Design V3 IEQ-13.
Application areas and surface suitability
Formulated to provide premium protection from staining to medium to high porosity fine stone, masonry, clay & cement products. Ideal applications include:
Marble, Limestone, Travertine
Sandstone & Bluestone
Cement & Clay pavers
Terracotta, Saltillo, Quarry
Ideal for all interior and exterior applications.
Excellent protection afforded to fine stone flooring and walls, outdoor stone features, patios, walkways, concrete and clay paving.
Expected Wear:
Stone Sealer Pro will provide premium protection for up to 5 years. However application methods, weather conditions, traffic, harsh cleaning methods and stone type will affect wear. Avoid use of solvents, strong acids and strong alkalis for extended sealer life.
Cleaning with Actichem Proneutro is advised.
It is recommended that the sealer be re-applied every 2 to 3 years where harsh conditions exist.
Considerations:
Not to be used as a sub-terrain waterproofing. Should not be applied if temperature is above 40 degrees or if rain is expected within 2 hours of application. If rain has preceded the application, the surface should be allowed 24 hours to dry completely.
How to use
Read and understand the SDS before use
Always pre-test in an inconspicuous location for sensitivity to chemicals.
Coverage can vary dramatically depending on the degree of porosity, but is normally 5 to 10 m2 / Lt per coat for open structure, highly porous substrates. And 10 to 20 m2 / Lt per coat for dense, less porous substrates.
Note:
Application on large concrete areas should be based on a preset coverage rate using a dedicated sprayer or painting equipment. No subsequent removal of excess product is required.
Surface Preparation:
New installations must be fully cured before application of Stone Sealer Pro (Min 48 hours, however some concrete installations may take up to 7 days to cure. Confirm with the structural engineer).
Existing stone and grout must be totally clean, dry and chemical free.
Coverage can vary dramatically depending on the degree of porosity, but is normally 5 to 15 m2 / Lt per coat for open structure, highly porous substrates and 10 to 20 m2 / Lt per coat for dense, less porous substrates.
Do not apply in direct sunlight. Temperature must be between 10°C and 28°C.
Highly absorbent surfaces may require two coats.
Dilutions
Ready to use
Application
Apply 1 to 3 coats of Stone Sealer Pro by generously saturating the surface using a polish applicator, roller or sprayer to an area which can be easily reached. (Approximately 15m2).
Ensure even coverage.
The surface must be shiny wet with a liquid film for at least 1 minute. For very porous substrates more sealer may need to be applied.
Allow 5 – 10 minutes for the sealer to absorb into the surface and then move the excess product with a squeegee to a new section.
If a second coat is to be applied, wait 20 to 30 minutes and repeat the process.
Using absorbent toweling or applicator, wipe off any sealer remaining on the surface after 10 minutes of the last application. Moisten the towel with Methylated Spirits to remove residues which have dried on the surface.
Allow 12 hours before returning area to traffic. Keep dry for 24 hours. Achieves a full cure in 24-48 hours.
Excellent phone manner and fast delivery
Great products and dast delivery.
Very Efficient & Helpful Service and Swift Delivery
The Operations of Diamach are Very Efficient and Swift