ACTICHEM Stone Sealer Gold Water Based Penetrating Sealer 15 Litre AP17715
Stone Sealer Gold
Ultimate waterbased penetrating stone and concrete sealer
Product Description
Stone Sealer Gold is a premium water-based penetrating sealer developed to provide long-lasting protection for marble, limestone, travertine, granite, and bluestone. It uses advanced flourochemical polymer technology to create a highly repellent surface that guards against water, oil, and general contaminants while preserving the stone’s natural look.
Stone Sealer Gold solves the challenge of maintaining the beauty and integrity of fine stone surfaces in both indoor and outdoor environments. Its deep-penetrating formula delivers up to 15 years of durable protection and is independently tested by a NATA-approved laboratory. Suitable for walls, floors, patios, and paving, it meets the Green Building Council of Australia’s Green Star requirements.
Floors & hard surfaces
Sealant
Stone & grout
pH
Water-Based
Dilution
Ready to use
Fragrance
None
Safety
Non-hazardous
Colour
Clear
Pack Size
5lt, 15lt, 500ml, 2.5Lt
Surfaces
Natural Stone, Concrete & Masonry
Product Code
AP177
Additional Information
Benefits
Premium Protection: Delivers up to 15 years of protection, independently performance-tested by a NATA-approved laboratory.
Precise Chemistry: Uses a blend of nano-sized fluorochemical technology and specialist penetrating solvents for deep penetration into dense substrates.
Comprehensive Protection: Guards against water and oil-borne contaminants, including food and beverage stains, oil and grease spills, biological growth (mould and mildew), spalling, efflorescence, pollution, and weathering.
Versatile Application: Water-based formula ensures easy application on a wide range of substrates.
Natural Look: Maintains the original appearance of fine stone without altering texture, slip characteristics, or colour.
Surface Safe: Will not etch or discolour marble or other fine stones.
Vapour Permeable: Allows natural stone to “breathe,” preventing moisture entrapment.
Safe to Use: Free from chlorinated hydrocarbons and not classified as a suspected carcinogen.
Application areas and surface suitability
Formulated to provide premium protection from staining to medium to high porosity fine stone, masonry, clay & cement products. Ideal applications include:
Marble, Limestone, Travertine
Sandstone & Bluestone
Cement & Clay pavers
Terracotta, Saltillo, Quarry
Ideal for all interior and exterior applications.
Excellent protection afforded to fine stone flooring and walls, outdoor stone features, patios, walkways, concrete and clay paving.
Expected Wear:
Stone Sealer Gold will provide excellent protection for up to 15 years. However application methods, weather conditions, traffic and harsh cleaning methods will affect wear. Avoid use of solvents, strong acids and strong alkalis for extended sealer life.
Cleaning with Actichem Proneutro is recommended. It is recommended that the sealer should be re-applied every 5 – 7 years where harsh conditions exist.
Considerations:
Not to be used as a sub-terrain waterproofing. Should not be applied if temperature is above 40 degrees or if rain is expected within 2 hours of application. If rain has preceded the application, the surface should be allowed 24 hours to dry completely.
How to use
Read and understand the SDS before use
Always pre-test in an inconspicuous location for sensitivity to chemicals.
Coverage can vary dramatically depending on the degree of porosity, but is normally 5 to 10 m2 / Lt per coat for open structure, highly porous substrates. And 10 to 20 m2 / Lt per coat for dense, less porous substrates.
Note:
Application on large concrete areas should be based on a preset coverage rate using a dedicated sprayer or painting equipment. No subsequent removal of excess product is required.
Surface Preparation:
New installations must be fully cured before application of Defender CSD 50 (Min 48 hours, however some concrete installations may take up to 7 days to cure. Confirm with the structural engineer).
Existing stone and grout must be totally clean, dry and chemical free.
Coverage can vary dramatically depending on the degree of porosity, but is normally 5 to 15 m2 / Lt per coat for open structure, highly porous substrates and 10 to 20 m2 / Lt per coat for dense, less porous substrates.
Do not apply in direct sunlight. Temperature must be between 10°C and 28°C.
Highly absorbent surfaces may require two coats.
Dilutions
Ready to use
Application
Apply 1 to 3 coats of Stone Sealer Gold by generously saturating the surface using a polish applicator, roller or sprayer to an area which can be easily reached. (Approximately 15m2).
Ensure even coverage.
The surface must be shiny wet with a liquid film for at least 1 minute. For very porous substrates more sealer may need to be applied.
Allow 5 – 10 minutes for the sealer to absorb into the surface and then move the excess product with a squeegee to a new section.
If a second coat is to be applied, wait 20 to 30 minutes and repeat the process.
Using absorbent toweling or applicator, wipe off any sealer remaining on the surface after 10 minutes of the last application. Moisten the towel with Methylated Spirits to remove residues which have dried on the surface.
Allow 12 hours before returning area to traffic. Keep dry for 24 hours. Achieves a full cure in 24-48 hours.
Excellent phone manner and fast delivery
Great products and dast delivery.
Very Efficient & Helpful Service and Swift Delivery
The Operations of Diamach are Very Efficient and Swift